How to recognize beep errors

How to recognize beep errors

When your computer beeps, it means that an error has occurred in the hardware . BIOS recognizes internal errors and sends signals in the form of beep sounds, indicating the location of the problem in the hardware. When you start your computer and hear strange beeps in the boot up process, it means trouble. It would be good to understand what the beeps mean. When your computer starts-up to perform a power-on self test or POST, then the booting problems are diagnosed with error codes displayed on the monitor. The computer architecture uses beeps to indicate an error in a number of patterns and timings of beeps when nothing is displayed on the monitor. Every BIOS has a unique code of beep. BIOS manufactures AMI and Award (now Phoenix) signal different codes for similar errors. 
It is not uncommon to get some beep sounds while starting your computer, and they correspond to different errors that can occur with your hardware. Below you will find a list of the most common errors and what they refer to. 

How to recognize the beep errors

Very short beep

This problem is linked to your motherboard. It can also mean that you are facing a problem with your system memory (BIOS AWARD)

Short beep

No problem.

Long beep followed by three sequential short beeps.

This issue is linked to your graphics card configurations.

Short beep followed by three sequential long beeps

You are facing a system memory problem.

Beep, pause, beep, pause, two sequential beeps

This error is linked to your CPU.

Three beeps, pause, three beeps, pause, four beeps

You have an issue with the video memory.

One long beep and nine short

Problem with the ROM (Bios AWARD).

Three beeps, pause, four beeps, pause, beep

This is linked to an error with your graphics card.

Four beeps, pause, three beeps, pause, beep

You have a system memory problem.

Five short beeps

You are facing a problem with your CPU.

Long constant beeps

Its a system memory problem. 

If your PC beeps after the OS has been launched, it may be due to the fact that your CPU is overheating and that could be a serious matter. 

if 1 beep its - video card 
if 2 to 3 beeps - RAM 
if it beeps continuously - it the processor 

REMEDY / SOLUTION : 
1. (VIDEO CARD)- remove the video card clean it up... you can use eraser...make sure to remove the dust/lint ..... 

2. (RAM)- If the problem is the ram ... its the same.. remove the ram clean it..the same as you clean the video card...but if you put back the ram to the slot...make it sure to lock it up and tighten up..just monitor it that its not loosen... 

3. (PROCESSOR) - remove the processor ... clean the white one i mean the paste 
(thermal paste) then if you dont have that paste try to ask the hardware im sure they have one and grab it... dont leave the processor if it is not attach in the slot make sure to have that paste first it has time limit in exposing the processor it may cause a problem if the processor wont put back int the slot.. <the main solution is change the thermal paste then lock it up tightly.. the most important thing is just...lock it up so tight..> 

that all... 

this is only my suggestions .... 

i hope it helps.... 

Computer POST and beep codes

Beep Codes AMI BIOS:
Error 1 short DRAM refresh
Disclaimer 2 short Parity circuit
3 short Base 64K memory failure
Disclaimer 4 short System timer
5 Short waiver process
6 short Keyboard controller Gate A20 error
7 short Virtual mode exception error
Disclaimer read / write test of 8 short Display memory
9 short checksum error BIOS ROM
Short stop 10 CMOS read / write
11 short Cache Memory error
1 long, 3 short Conventional / Extended memory failure
1 long, 8 short Display / Retrace test fails
two-tone siren low speed fan, the voltage level of the question
IBM BIOS Beep:
No Beep No Power, Loose Card, or Short.
1 short beep regular mail, the computer normally.
2 short beeps POST error, review screen error code.
Continuous Sound No Power, Loose Card, or Short.
Repeating short beep without power, power, cards, or short.
1 long and 1 short Motherboard sound issue.
1 long and 2 short beeps Video (Mono / CGA Display signal) question.
1 long and 3 short beeps. Video (EGA) display circuit.
3 long beeps the keypad or keyboard card error.
1 Beep, Blank or incorrect display of the video shows the scheme.
Award BIOS Beep:
1 long, 2 short Video Indicates an error has occurred and the BIOS can not initialize the video screen to display additional information
1 long, 3 short video card is not detected (reinstalling video card) or a bad video card
Signals infinite repetition of RAM problem.
Repeated high-frequency sound while the computer is overheating processor (CPU)
Repeated sound alternating high and low frequency is a problem with the processor (CPU), may be damaged
Phoenix BIOS Beep:
1-1-1-1 beep code unconfirmed. Reinstall the memory chips or replace RAM chips as a possible solution
1-1-1-3 Check real-time.
1-1-2-1 Get CPU type.
1-1-2-3 system hardware initialization.
1-1-3-1 Initialize chipset registers with initial values ??POST.
1-1-3-2 Set in POST flag.
1-1-3-3 initializing the processor registers.
1-1-4-1 cache initialization initial value POST.
1-1-4-3 initialization I / O.
1-2-1-1 initialization power management.
1-2-1-2 Load alternate registers with initial values ??of POST.
1-2-1-3 Go to UserPatch0.
1-2-2-1 Keyboard controller initialization.
1-2-2-3 BIOS ROM checksum.
1-2-3-1 timer initialization 8254.
1-2-3-3 DMA controller initialization.
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM upgrade.
1-3-1-3 Test 8742 keyboard controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 Autosize DRAM.
1-3-3-3 Clear 512K base memory.
1-3-4-1 Test 512 base address lines.
1-3-4-3 Test 512K base memory.
1-4-1-3 Test processor bus clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Setting the chipset registers. Extended
1-4-4-2 Load alternate registers with the values ??of CMOS.
2-1-1-1 Set Initial speed of the processor.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 BIOS initialization interrupts.
2-1-2-3 Check ROM copyright.
2-1-2-4 manager PCI initialization parameters discs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 initialize the PCI bus and devices.
2-1-3-3 initialize all display adapters in the system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display type and speed of the processor.
2-2-1-3 Test keyboard.
2-2-2-1 set of keys, press, if enabled.
2-2-2-3 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display quickly press F2 to enter SETUP.
2-2-4-1 Test RAM between 512 and 640K.
2-3-1-1 Test extended memory.
2-3-1-3 Test extended memory address lines.
2-3-2-1 Go to UserPatch1.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow of the message.
2-3-4-3 Display without disposable segments.
2-4-1-1 error messages. Show
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for errors Keyboard
2-4-4-1 Setting up hardware interrupt vectors.
2-4-4-3 test coprocessor, if present.
3-1-1-1 Disable onboard I / O ports.
3-1-1-3 definition and installation of external ports RS232.
3-1-2-1 detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I / O ports.
3-1-3-1 initialization BIOS Data Area ,.
3-1-3-3 BIOS Extended initialization data area.
3-1-4-1 Initialize the floppy controller.
3-2-1-1 initialize the hard disk controller.
3-2-1-2 initialize local bus hard disk controller.
3-2-1-3 Go to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 option Shadow ROM.
3-2-4-1 Setting the power management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase F2 prompt.
3-3-3-3 scanning stroke key F2.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in POST flag.
3-4-1-1 Check for errors
3-4-1-3 POST done - prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.
3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown error interrupts.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-1 Disable error.
4-2-3-3 Extended Block Move.
4-2-4-1 10 Error Turn off
4-3-1-3 initialization chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM OK.
4-3-2-4 complete test whether the RAM.
4-3-3-1 initialize any OEM.
4-3-3-2 interrupt controller initialization.
4-3-3-3 Read in bootstrap code.
4-3-3-4 all initialization vectors.
4-3-4-1 download program flash.
4-3-4-2 initialize the boot device.
4-3-4-3 Boot code was read OK.
two-tone siren low speed fan, the voltage level of the question
DELL PC
1 long, 2 short Video Indicates an error has occurred and the BIOS can not initialize the video screen to display additional information
1 long, 3 short video card is not detected (reinstalling video card) or a bad video card
Signals infinite repetition of RAM problem.
Repeated high-frequency sound while the computer is overheating processor (CPU)
Repeated sound alternating high and low frequency is a problem with the processor (CPU), may be damaged
MACINTOSH SdSTURTUP voice:
Error tone. (two sets of different colors) The problem with the motherboard or SCSI bus.
Startup tone, drive back, there is no problem with the video controller video.
The powers of the tone is not. The problem the board.
High tone, four higher tones. The problem with the SIMM.



Please buck-up your registry simply by export it  in order to proceed

Download software here it is free!


ALSO PLEASE VISIT THIS VIDEOS AND SEE IF YOU FIND SOMETHING NEED:

Windows Registry Tools can be downloaded here:
How to kip your PC Private by deleting DATA Permanently
http://askpctech.blogspot.com/2016/03/kip-your-pc-privat.html


This tutorial is made up on request several  users, is well is fallowing video:
1)How to Delete Paint Recent Pictures from List in Windows 7
https://youtu.be/9fBn1SfeMps
2)Win 7– Fix for “Safely Remove Hardware and Eject Media” not working How To
https://www.youtube.com/watch?v=xNYEE0TYS-U
3)Windows 10 How to Fix Black Screen After Booting
https://www.youtube.com/watch?v=yXClRD1CsNQ
4)How To Remove Windows 10 Upgrade Notification On Windows 7 And Windows 8
https://www.youtube.com/watch?v=11QqCzam_nI
5)How to Delete Face book Page Permanently - 2015
https://www.youtube.com/watch?v=_6AVoeCJZjU
6)How to Uninstall Windows 10 and Downgrade to Windows 7 or 8.1
https://www.youtube.com/watch?v=gJcuup_E_Uw
7)detected: not-a-virus:remoteadmin.win32
https://www.youtube.com/watch?v=V3vukcM4UVc
8)How to change pictures into icons for folders
https://www.youtube.com/watch?v=qb8i8Yowqjk
9)Speed up your PC Disable System Restore on SSD
https://www.youtube.com/watch?v=HW7zh4d7iOo
10)Speed up your PC Disable Scheduled De-fragmentation SSD
https://www.youtube.com/watch?v=drqlPnmsfXU
11)2015 Black screen of DEATH Windows 7 & 8 - with cursor at start-up SOLVED
https://www.youtube.com/watch?v=AtyAOTdfKD0
12)Upon start up only wallpaper shows FIX
 http://youtu.be/HQa-QdFjKVI
13)Here is video on Windows 7 & 8 - Black screen with cursor at start-up FIX
http://youtu.be/AtyAOTdfKD0
You can also open Task Manager by pressing Ctrl+Shift+Esc.
14) I bought a windows 7 PC but it Look alike old PC FIX:
http://youtu.be/hDxpcgBo39c
15) Windows 7 & 8 - Black screen with cursor at start-up FIX:
http://youtu.be/AtyAOTdfKD0
16) How To Fix Minecraft OpenGL Error Windows 7 xp vista 720p :
http://youtu.be/JZ9u-0XJcSA
17) removing bars using regscanner regedit & file shredder 720p:
http://youtu.be/geDYSGIxTnc
18) How to Recover windows Explorer from error 2014 720p
http://youtu.be/24Q36kz7INM
19) HOW TO Save on battery online
http://youtu.be/GpGNgI-YK7E
20) Windows 7 & 8 - Black screen with cursor at start-up FIX
http://youtu.be/AtyAOTdfKD0
Upon start up only wallpaper shows no icons
CTL+ALT+DEL then click file and new task. then type explorer.exe and press ok
Best Greenhouse system 2015 http://youtu.be/mIt5Xh0Kn9k

Go to link Download